Skip to Content
SecureAS Crimson Series

Multi-Browser NVR 

Activation Guide

Activate and configure your SecureAS Crimson Series NVR completely through a web browser without connecting a monitor or screen to the NVR.

↓ Download Multi-Browser Plugin View Installation Guide
Overview

Complete NVR setup without a monitor

The SecureAS Crimson Series allows technicians to activate, configure and manage a new NVR directly from a PC browser connected to the NVR network. This removes the need for a dedicated display during initial installation.

01

Browser-Based Activation

Access the NVR through its IP address and complete the initial activation without using an HDMI or VGA monitor.

02

Remote Configuration

Configure passwords, storage, parameters and network cameras directly from the browser interface.

03

Faster Installation

Reduce hardware requirements and simplify field deployment when a monitor is not available.

Step-by-Step

Activate and configure your NVR

Follow these steps to prepare a new SecureAS Crimson Series NVR for operation.

01

Connect and access the NVR

Connect your PC and the NVR to the same network. Open a supported web browser and enter the NVR IP address.

  • No dedicated monitor is required.
  • Use a PC connected to the NVR network.
  • Open the NVR IP address in the browser.
02

Install the Multi-Browser Plugin

The first browser session requires the SecureAS Multi-Browser Plugin for complete NVR control.

  • Download the plugin from the official SecureAS source.
  • Run the lightweight installation package.
  • Complete the standard installation process.
  • Refresh the browser after installation.
03

Create the NVR password

On the initial login, the NVR requires a new password before configuration can continue.

  • Username: admin
  • Enter the newly created password.
  • Save the password securely.
  • Confirm the successful password setup.
04

Format the hard disk

A newly installed hard disk will initially appear as unformatted and must be prepared for recording.

  • Open the storage or disk management section.
  • Select the unformatted hard disk.
  • Click Format Disk.
  • Confirm that the disk status becomes Normal.
05

Configure basic parameters

Configure the basic system preferences after completing the initial activation.

  • Select the appropriate timezone.
  • Configure the system language.
  • Review the SecureAS cloud ID information.
  • Review available VMS application information.
06

Reboot the NVR

Rebooting the NVR is an important part of the initial activation process.

  • Initiate reboot from the browser interface.
  • Wait for the NVR to restart completely.
  • Log in again using the new password.
  • Continue with camera configuration.
Configuration

Manage the NVR directly from the browser

After activation and reboot, additional system and camera configuration can be completed remotely.

Remote NVR Management

Essential configuration functions remain accessible through the browser interface.

  • NVR activation and password management
  • Hard disk formatting and storage status
  • Timezone and language configuration
  • Network and IP configuration
  • IP camera discovery and channel assignment
  • Main stream and sub-stream live viewing

Installation Advantages

A browser-based workflow helps field technicians complete installations with fewer physical hardware requirements.

  • No monitor required at the NVR location
  • Faster initial deployment
  • Centralized browser-based configuration
  • Easier IP address management
  • Reduced installation delays
IP Camera Setup

Add and configure IP cameras remotely

Once the NVR has been activated and rebooted, cameras can be discovered and added directly through the browser interface.

Enable Channels

Enable the required IP camera channels through remote settings.

Search Devices

Search the network to discover compatible SecureAS IP cameras.

SecureAS Protocol

Use the SecureAS discovery process to locate available cameras.

Change Camera IP

Camera network addresses can be modified directly from the interface.

192.168.1.88 → 192.168.1.89

Assign Channel

Select the camera and assign it to the required NVR channel.

View Live Feed

Select the main stream or sub-stream to view the camera feed.

Quick Reference

Complete activation workflow

Step Action Key Operation Expected Result
01 Install Plugin Install SecureAS Multi-Browser Plugin Full browser NVR interface available
02 Set Password Log in as admin and create a password Secure NVR access enabled
03 Format HDD Select the unformatted disk and format it Disk status becomes Normal
04 Basic Settings Configure timezone and language System parameters personalized
05 Reboot NVR Restart the NVR from the browser Initial activation is finalized
06 Add Cameras Search, configure and assign IP cameras Cameras available for live viewing
Key Benefits

Built for efficient field deployment

The browser-based activation workflow helps installers complete essential NVR setup even when a dedicated display is unavailable.

01 No dedicated monitor required
02 Browser-based activation
03 Remote IP camera configuration
04 Faster installation workflow

Ready to configure your SecureAS NVR?

Download the SecureAS Multi-Browser Plugin and follow the browser-based activation workflow to complete your Crimson Series NVR installation without a dedicated monitor.

↓ Download Multi-Browser Plugin